2120 4 Slot Crimping Tool - Approximately 20” long, this tool has four different sized grooves, which are marked to indicate the proper size sleeve for different gauges of wire. This tool works with crimping sleeves only.

1-2 Groove - Fits 1-2 Crimping Sleeves for 14-16 Gauge Wire
2-3 Groove - Fits 2-3 Crimping Sleeves both long and short for 12 ½ Gauge High Tensile Wire.
3-4 Groove - Fits 3-4 Crimping Sleeves for 10-11 Gauge Wire
4-5 Groove - Fits 4-5 Crimping Sleeves for 9 Gauge Barbed Wire

2125 4 In 1 Eze-Pull Crimping Tool - This contractor quality crimping tool is designed to give you years of use. It is designed to crimp C2-3 Crimping sleeves or 12 ½ gauge high tensile wire. The shorter handles are preferred byinstallers. The built in staple puller removes even the toughest of staples with ease. It contains a built in wire cutter. Lightweight and compact is ideal for stripping coating on products such as Horsecote (7100) and Hotcote. (7120) The most popular crimping
tool.

Do not use a set of bolt cutters to crimp your crimping sleeves, it will not give you full holding strength.

2140 Hayes Chain Grab Wire Puller - Used to pull up to ends of high tensile smooth wire for joining with crimping sleeves or other method. Works like a comealong, but with smooth jaws that will not scratch or damage your galvanization on your

2150 Hayes Stretcher Bar Puller - Also known as a clamp strainer, this unique tool is used to join two Hayes Stretcher Bars (2160-2185). The jaws of the tool hook into the Hayes Stretcher Bar at either end and the teeth of walk up the long 6' chain pulling the two Stretcher Bars together and standing them into position from the ground. Recommend using 2 when using a center pull system. A must for building woven wire, will work on any size Hayes Stretcher Bar. Smooth jaws prevent scraping of the wire.

2160 Hayes 4' Stretcher Bar W/Wedges 52” - 52” in height for 4' woven wire. Different size heights available for different woven wire heights. These bars can be used to center pull or end pull. (Note: Pulling with a tractor on an end pull can result in damaging the bar.) Use these tools to join two rolls and crimp using the proper gauge crimping sleeves for a perfect join.

2180 Hayes 6' Stretcher Bar 76” - for use with 6' woven wire.
2185 Hayes 8' Stretcher Bar 102” - for use with 8' woven wire.

Page 4

2190 Wire Twisting Tool - The old fashioned way of twisting wire to tie off ends or to join. Simply slip the end of the wire in the hole and twist end over end. It makes a clean and professional tied end.



2195 Gripple Tool - This tool works with any size Gripple product. The tool will allow to tension, retention, strain, restrain, join and rejoin. Ideal for working with woven wire.

Wire Joiners




3100 C2-3 Crimps - Crimping Sleeves to be used with crimping tools for joining wire. Use two sleeves when joining wire back onto itself. When joining wire from a break or adding a new roll use 3 crimping sleeves. This will give your wire the same strength as if it were never joined or broken. This is only done when using a proper crimping tool. 300 pieces per bottle

3110 12 ½ Ga. Double Crimping Sleeves - Double length 2-3 crimping sleeves. These longer sleeves equal 2 short sleeves. When using the double length sleeve, one will provide you with full strength when joining back onto itself or joining full rolls. The longer length makes it easier to handle. Simply use your crimping tool to crimp the entire length of the sleeve. Fits the 2-3 groove in your crimping tool. 100 pieces per bottle.

3120 16 Ga. Crimping Sleeves - Used to crimp 14-16 gauge high tensile wire. Fits the 1-2 groove in your crimping tool. Bag of 100.

3130 10-11 Gauge Crimping Sleeves -Used to fit 10-11 gauge high tensile wire. Fits the 3-4 groove in your crimping tool.

3140 9 Gauge Crimping Sleeves - Used to fit 9-gauge barbwire. Fits the groove 4-5 in your crimping tool.


 



3150 Electric Fence Taps - Used to join wire to an existing wire fence. You can use the fence tap when jumping electric from one hot wire to another. Fits the groove 3-4 in your crimping tool. Box of 100.

3160 Wire Links - Joining device. Put the one end of a broken wire into each end of the Wire Link, it will hold securely with out use of any tools. Simply go back to your in-line wire strainer (4100) and using your In-Line Handle (2110) restore the tension. A good product to have on hand for those quick fixes of a broken wire.

3170 Wire Vises - When it is necessary to have a smooth fence line, no protruding strainers then the Wire Vise is the answer. Used in the vineyard industry for many years. Drill a 3/8” hole in the end of your end post and insert your Wire Vise. Insert your wire into the Wire Vise and pull with a Wire Vise Puller or by hand. This will secure the wire.

Sizing Chart

1-2 Sleeves fit 14-16 gauge high tensile wire
2-3 Sleeves fit 12 -½ gauge high tensile wire
3-4 Sleeves fit 10-11 gauge high tensile wire
4-5 Sleeves fit 9-gauge barb wire
Wire Vises & Links fit 12-½ gauge high tensile wire